How to Get More FPS: 12 PC Settings That Actually Boost Gaming Performance
Your PC is probably faster than your frame rate suggests. I have seen the same RTX 4060 system jump from 74 FPS to over 110 FPS in the same game, on the same map, without spending a dollar — just by fixing settings that were quietly holding it back. If you are trying to figure out how to get more FPS, start with configuration, not a shopping cart. Most gaming PCs leave 15 to 40 percent of their performance on the table.
Below are the 12 settings that actually move the number — the display, Windows, driver, and in-game options I test first on every build.
Before you change anything, get a baseline. Run your game for five minutes in a demanding area, not the menu, and note your average FPS and 1% lows using the Steam overlay or Xbox Game Bar (Win + G). Retest the same scene after each group of changes.
How to Get More FPS With Display and Windows Settings
1. Set Your Monitor to Its Real Refresh Rate
Windows frequently leaves a 144Hz or 165Hz monitor running at 60Hz after a fresh install, cable swap, or driver update. Go to Settings > System > Display > Advanced display and select the highest refresh rate listed. Use DisplayPort if you can — many HDMI cables and older ports cap at 120Hz at 1440p or 60Hz at 4K. If your FPS counter is high but the game still feels like 60, this was the problem.
2. Turn On Game Mode and Hardware-Accelerated GPU Scheduling
Enable Game Mode under Settings > Gaming. It stops Windows Update installing drivers mid-session and cuts background interruptions. In Graphics settings, also enable Hardware-accelerated GPU scheduling and restart. On RTX and RX 6000/7000 cards it typically adds 2 to 5 percent and improves frame pacing. Add your main games there and set them to High performance — especially on laptops, where this fixes games running on integrated graphics.
3. Use a High-Performance Power Plan
Balanced plans save electricity, not boost clocks. On a desktop, select High performance in Control Panel > Power Options, and on Windows 11 set Power mode to Best performance. Laptops gain the most: a performance profile in Armoury Crate or MSI Center can raise the GPU limit from 80W to 115W, worth 10 to 20 FPS. Always game plugged in.
4. Enable XMP or EXPO for Your RAM
If you bought 3600MHz or 6000MHz RAM and never entered the BIOS, it may be running at 2133MHz or 4800MHz. Restart, tap Delete or F2, and enable XMP on Intel or EXPO/DOCP on AMD — usually a single toggle on the main BIOS screen. CPU-limited games like Valorant, CS2, Fortnite, and Microsoft Flight Simulator respond best, with 10 to 20 percent better minimum FPS being common. If it fails to boot, clear CMOS and try the second, slightly slower profile.
GPU and System Settings Most Players Skip
5. Turn On Resizable BAR
Resizable BAR lets your CPU access the full GPU frame buffer at once instead of in 256MB chunks, and it is often disabled on older motherboards. Check it in NVIDIA Control Panel > System Information or AMD Software. If it is off, you usually need a BIOS update, Above 4G Decoding enabled, Re-Size BAR Support set to Auto, and CSM disabled. Expect 3 to 10 percent in supported games.
6. Set Driver Power and Latency Options
Update your driver cleanly first, direct from NVIDIA or AMD, choosing Custom/Factory Reset if offered. Then set just two options:
- NVIDIA: In Manage 3D Settings, set Power management mode to Prefer maximum performance in the game profile (not globally, or the GPU idles hot), and Low Latency Mode to On, or Ultra in GPU-limited competitive games.
- AMD: Enable Radeon Anti-Lag and set Texture Filtering Quality to Performance if you need every last frame.
Ignore lists of 20 global driver tweaks. Most do nothing on current drivers.
7. Kill Background Apps and Overlays
Chrome with 18 tabs, Discord, RGB software, and three overlapping overlays each cost a little, and together they cost a lot on a 6-core CPU or 16GB of RAM. In Task Manager > Startup apps, disable anything non-essential. Pick one FPS overlay, not three. On a 16GB system, freeing 2–3GB can eliminate the hitching behind bad 1% lows, even when average FPS looks fine.
8. Keep Temperatures Under the Throttle Line
A GPU at 83–87°C pulls back its boost clock, and a CPU at 95–100°C does the same. If FPS starts strong and fades after 15 minutes, heat is the issue. Clear dust, confirm your intake and exhaust fans are spinning, and set a more aggressive fan curve in Afterburner or AMD Software. Undervolting helps too: an RTX 4070 at 0.95V often holds the same clock 8–12°C cooler.
In-Game Settings With the Biggest Payoff
9. Use DLSS, FSR, or XeSS
Upscaling is the biggest free lever in modern games. DLSS (RTX cards), FSR 2/3 (almost any GPU), and XeSS render at a lower internal resolution, then reconstruct a sharp image.
- Start on Quality. At 1440p it renders internally around 1707 x 960 and typically gains 25 to 40 percent FPS, very close to native in quality.
- Use Balanced only if you are still short of your target. Save Performance for 4K.
- Enable Frame Generation (DLSS 3 or FSR 3) only if your base rate is already 55–60 FPS. It improves smoothness but does not reduce input lag, so below that baseline shooters can feel worse.
If you want to know how to get more FPS without making a game look like soup, this is usually the answer.
10. Cut Shadows, Volumetrics, and Reflections First
Not all settings cost the same. Lower these first, in this order:
- Volumetric fog/clouds: often 15 to 25 percent alone. Medium is the sweet spot.
- Shadow quality/resolution: High instead of Ultra frequently gains 8 to 12 percent.
- Reflections and ray tracing: turn RT off first in fast-paced games — RT reflections and global illumination can halve FPS.
- Ambient occlusion: Medium or High instead of Ultra.
Keep texture quality high if your VRAM allows it. Textures mostly use memory, not compute, so they are usually close to free.
11. Match Textures to Your VRAM
Texture stutter is usually a VRAM problem. As a guide: 8GB handles High textures at 1080p and Medium–High at 1440p, 12GB is comfortable at High/Ultra at 1440p, and 16GB gives headroom at 4K. If the game shows a VRAM meter, stay under about 90 percent of it. Do raise anisotropic filtering to 8x or 16x — it costs almost nothing and looks far better.
12. Disable In-Game V-Sync and Cap Smartly
Classic V-Sync adds input lag and can slam you from 144 FPS to 72, or 60 to 30, when you miss the target. With a G-Sync or FreeSync monitor, do this instead:
- Enable G-Sync/FreeSync in the driver and the monitor menu.
- Turn V-Sync OFF in the game.
- Cap FPS to 3 below your refresh rate — 141 on 144Hz, 237 on 240Hz — with the in-game limiter or RivaTuner. You stay inside the variable-refresh window, so tearing disappears without the lag penalty.
No variable-refresh monitor? A locked 60 you can actually hold feels smoother than a number bouncing between 55 and 85. Consistency beats a higher average.
Frequently Asked Questions
What is the fastest way to get more FPS without upgrading?
Enable DLSS or FSR on Quality, drop volumetrics and shadows from Ultra to Medium or High, and confirm your monitor is at its full refresh rate. On most systems those three changes deliver 30 to 50 percent in under ten minutes.
Will adding more RAM increase my FPS?
Only if you are running out. Going from 8GB to 16GB can transform a stuttery system, but if you already have 16GB and in-game usage stays under 13–14GB, extra RAM adds almost nothing. Past 16GB, speed and enabling XMP/EXPO matter more than capacity for most players.
Does lowering my resolution really help?
Yes. 1440p has 78 percent more pixels than 1080p, and 4K has four times as many. Dropping a render-resolution slider to 85 percent can gain 20 to 40 percent. Upscaling is usually the smarter version of the same trade, because your output resolution and HUD stay sharp.
Why is my FPS high but the game still stutters?
Check your 1% lows, not the average. Stutter usually comes from VRAM overflow, a single overloaded CPU thread, shader compilation, background apps, or thermal throttling. Matching textures to VRAM, closing apps, clean drivers, and better cooling target the lows — what you actually feel.
Conclusion
You do not need all 12. On most PCs, four do most of the work: the correct refresh rate, XMP/EXPO on, upscaling on Quality, and Ultra shadows and volumetrics trimmed back. Retest the same scene after each group, and stop when you hold a stable rate at or just under your refresh rate. That stability is what a well-tuned PC feels like.
2 Comments